Description

Original water pump for Zanussi dryer | 8581258349217

The original Zanussi water pump, part number 8581258349217, drains the water that is created during drying.
A pump malfunction causes the dryer to stop drying and display an E22 error.
Replacing with an original part restores the dryer to full functionality.

The dryer stops drying? The pump may be faulty.

When the water pump breaks down, condensation builds up inside the dryer.
As a result, the dryer detects an abnormal water level and stops the heating operation.
Sometimes it displays error code E22, which indicates a condensation drainage failure.
Before calling a technician, make sure the water tank is empty and the filters are clean.
If the problem persists, the pump likely needs to be replaced. Click the “Check Model Compatibility” button at the top of the page before ordering.

How does the water pump in a dryer work?

During drying, the condenser cools the hot vapor and produces water.
The water pump sucks up this water and drains it into the drain pipe or collection tank.
The pump motor runs on 240V, 50Hz and drives a small impeller that pushes the water out. When the motor burns out or the impeller gets stuck, drainage stops completely.

✅ An original water pump ensures proper drainage and the device's integrity for years.

✅ Why is it mandatory to use only original parts?

The pump manufacturer Hanyu manufactures the component according to precise electrical specifications: 240V, 50Hz, 5W, 0.15A.
This specification ensures that the pump works in full synchronization with the dryer's control card.
In addition, the original pump withstands rigorous durability tests for a humid and hot environment over the years.
An unapproved pump, however, may disrupt the control circuits and cause further damage that costs much more than a simple replacement.

📍 How do you find the dryer model?

You will find the model number on the inside of the door, next to the opening rubber.
The sticker indicates the full model number and the PNC code (11 digits). Together, these two pieces of information allow you to verify that the part is compatible with your dryer.

Technical

✅ Compatible models

The part fits the following models. Make sure it matches the PNC code on the sticker:

Zanussi Zanussi:

• ZDPB274

⚠️ To check exact compatibility for your model, click the “Check Model Compatibility” button at the top of the page.

Installation instructions

⚠️ It is important: Replacing a water pump involves working on an electrical component that is directly connected to the dryer's control circuit.
This is a replacement that requires professional technical knowledge. Unprofessional installation may cause additional damage and compromise the integrity of the device and safety of use.
It is recommended to call a certified technician from the official service. To book a technician in your area – click hereCost of technician arrival: 290 NIS (not including the cost of the part).

💡 Tip from the experts

To extend the life of the water pump, clean the lint filter after each drying and the condenser unit once a month.
Dirt that builds up in the condenser increases the amount of water the pump has to drain with each cycle. Such overloading significantly shortens the life of the pump.

❓ Frequently Asked Questions

Why does the dryer stop drying and display an E22 error?
Error E22 on a Benzos indicates a failure to drain the condensation. Most often the cause is a faulty water pump that is not draining the condensation water.
In addition, sometimes the cause is a clogged filter or a dirty condenser.
Therefore, it is recommended to clean the filters first. If the error persists after that, it is likely that the pump requires replacement.

Can the water pump be replaced by yourself?
Replacing a water pump involves disconnecting electrical connections and pressure hoses inside the dryer.
This is an operation that requires professional technical knowledge.
Therefore, to maintain the integrity of the device and the safety of use, it is recommended to call a certified technician from the official service. Cost of technician arrival: 290 NIS.

What is the difference between the water pump and the condenser?
The condenser is the component that cools the moisture vapor and produces the water. The pump, on the other hand, sucks the water created in the condenser and drains it out.
So these are two different components that work together. A malfunction in one of them causes the same result: the dryer stops drying.

Is the water pump also suitable for AEG and Electrolux models?
The water pump (Hanyu B13-6B) was also originally used in various AEG Lavatherm and Electrolux EDC models.
Since the pump supplied is specific to the Zanussi ZDPB274 model, it is mandatory to verify compatibility with the exact model before any order.
Click “Check Model Compatibility” at the top of the page.

How long does it take for a technician to replace the pump?
An experienced technician can usually replace the water pump in 30 to 45 minutes.
After replacement, the technician runs a short drying cycle to make sure drainage is proper and the E22 error code is gone.

⏱️ Delivery times:

• Most localities: within 10 business days
• Golan Heights, Arava, Eilat and settlements beyond the Green Line: within 10 business days